Login | Sign Up
ErrorKey - Search engine for Error codes and messages     
  Cisco IOS:RSP  [ 95 result(s) ]
CISCO 6400 CISCO IOS 
  -  %RSP-3-MSFIX : Fixing [chars] by setting to default [chars]  CISCO IOS
The characters shown can be either on the slave RSP setting or on the master RSP setting. The ROM monitor default slave RSP setting is not synchronized with the system configuration file specifications. During bootup, the system image detects the mismatch and modifies the ROM monitor setting to conform with these specifications. This mismatch most likely occurred because a new RSP was being installed and booted in a high system availability (HSA) environment (dual RSPs) for the first time. Alternatively, in established HSA configurations, this message may result from a previous Interprocess Communication (IPC) error occurring while the HSA environment is reconfigured.
Using the show version or show boot commands, determine which slot contains the current slave RSP. Using the show configuration command, determine which slot has been specified as the default slave RSP. If there is no slave default-slot command in the configuration file, the value defaults to the highest numbered CPU slot (slot 3 on a Cisco 7507, and slot 7 on a Cisco 7513). If the slot number obtained in Step 1 is the same as the number obtained in Step 2, then no further action is required. You have configured HSA in simple hardware backup mode, and both RSPs are identical. However, if the two slot numbers differ, you have configured HSA in software error protection mode, and will have different images running, depending on which RSP is currently the slave RSP. If the slot numbers discovered in Steps 1 and 2 differ, reload your router to ensure that the desired system image is running. After the reload, the actual slave RSP will match the default slave RSP specified in (or inferred from) the system configuration file. For details of various HSA configuration modes consult the Cisco IOS Configuration Fundamentals Configuration Guide.
Cisco IOS
Comments
 
  -  %IPC-5-SLAVELOG : VIP-[chars]  CISCO IOS
The Cisco IOS software, running on a Versatile Interface Processor (VIP) card, generated this message. The error message has been passed up to the Route Processor (RP) or Route Switch Processor (RSP) for display. This message appears only if the user has configured the service slavelog command.
Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Cisco IOS
Comments
 
  -  %RSP-4-RSPDRAM : Insufficient DRAM to adequately run this IOS version. [dec]M is recommended  CISCO IOS
The quantity of RSP DRAM is below the recommended amount.
Add DRAM.
Cisco IOS
Comments
 
  -  %APPN-3-lognofENV_RSP_INV_CORREL : NOF received PE_CREATE_ENVIRONMENT_RSP with invalid correlator  CISCO IOS
Node operator facility (NOF) received a response interprocess signal (IPS) (PE_CREATE_ENVIRONMENT_RSP) that it could not correlate.
The response is from a request to create an environment, probably in an attached coprocessor. NOF could not correlate the response to any of its outstanding creation requests. There is an internal code problem in the local NOF or environment manager. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Cisco IOS
Comments
 
  -  %APPN-3-lognofEXCEPTION_RSP_RCVD : NOF received exception response, sense_code = [hex], ips_name = [hex]  CISCO IOS
A node component encountered an error while processing a node operator facility (NOF) request.
The other component sent an EXCEPTION_RSP IPS message indicating the failure. The EXCEPTION_RSP message contains a sense code that identifies the cause of the failure. Probable causes of this error are an unrecoverable system error, detection of a configuration error by the node, not all required software components being installed or available for use by the node, a serious memory shortage, or an internal code problem. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Cisco IOS
Comments
 
  -  %CBUS-3-DAUGHTER_NO_RSP : Unit [dec], daughter [dec], not responding (0x[hex]) - disabled  CISCO IOS
A hardware component failed an internal diagnostic test. Test output and descriptions of ranges follow. Unit [dec] (ranges 0-14): Indicates the Multibus jumper setting for the ciscoBus controller. daughter controller [dec] (ranges 0-3): Indicates the ciscoBus relative slot number (0 to 3, or in the Cisco 7000, 0 to 4) of the daughter card that failed the test. The daughter card's hardware was recognized across the ciscoBus backplane, but the daughter card did not respond to the first command issued to it. This condition is a result of one of the following: the daughter card did not reset, the microcode on the card is in a hung state, or the card cannot fully communicate across the ciscoBus backplane (cannot read or write shared MEMD or does not get the MALU_ATTENTION signal across the ciscoBus).
First, ensure that the daughter card is properly seated in its Multibus and ciscoBus connectors. If the message recurs, call your technical support representative.
Cisco IOS
Comments
 
  -  %APPN-3-logcsCS_ACT_AS_RSP_UNKWN_LPID : CS - ACT_AS_RSP UNKNOWN LPID: lpid = [hex]  CISCO IOS
The link station identified in the received response does not exist.
Configuration services (CS) received an ACTIVATE_AS_RSP interprocess signal (IPS) specifying a link-station control block that is invalid or no longer exists. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Cisco IOS
Comments
 
  -  %RSP-3-SLAVECHANGE : Slave changed state from [chars] to [chars]  CISCO IOS
The slave RSP has undergone a hardware state change. Both the old state and new states are shown. Possible states are nonparticipant, slave, master, and unplugged. Possible state changes indicated by this message are any to unplugged, unplugged to nonparticipant, nonparticipant to slave or slave to nonparticipant. Any other combination is unexpected.
The following actions are recommended: •If the slave RSP has been removed, consider reinstalling it if continued high system availability (HSA) operation is required. If the slave RSP is present, ensure that it is properly seated in the card cage. •If a slave RSP has been installed, configure the router for HSA. See the Configuration Fundamentals Configuration Guide for more details. In particular, use the slave auto-sync config command to ensure that the new slave RSP is configured consistently with the current master RSP. -------------------------------------------------------------------------------- Caution Failure to ensure a consistent configuration on a freshly installed slave RSP might result in undefined behavior if the router reloads. -------------------------------------------------------------------------------- •If a previously crashed slave RSP has been reset, or a newly installed slave RSP is in transition from unplugged to nonparticipant, and finally to slave state. No action is required. •If the slave RSP image has crashed, log in to the slave RSP's console using the if-console slot command. You will now be connected to the ROM monitor prompt on the slave RSP. Diagnose the slave RSP failure. For example, capture the output from the stack and context ROM monitor commands. Provide that information to your technical support representative, along with the router's configuration and any other relevant information, so that the problem
Cisco IOS
Comments
 
  -  %RSP-4-HSA_MEM : size mismatch, master [int]MB, slave [int]MB  CISCO IOS
Memory size mismatch between a master and a slave RSP.
Configure both master and slave RSPs to have an equal amount of memory.
Cisco IOS
Comments
 
  -  %IPC-5-SLAVELOG : VIP-[chars]  CISCO IOS
The Cisco IOS software, running on a Versatile Interface Processor (VIP) card, generated this message. The error message has been passed up to the Route Processor (RP) or Route Switch Processor (RSP) for display. This message appears only if the user has configured the service slavelog command.
Copy the error message exactly as it appears on the console, and report it to your technical support representative.
Cisco IOS
Comments
 
 

 
Cisco IOS (93)
RSP  (2)
 
  Prev   1  2  3  4  5  6  7  8  9  10  Next